ezVision Video iWear:
Baru BR-3000:
If your problem persist or to ask question you did not find
in the FAQ section, please contact
info@mobilmedya.net
·
Is the unit
powered on?
Be sure the Blue
LED on the converter/battery pack is illuminated.
·
Is the unit
plugged in?
In instances
where you want to use the unit, but have not charged the battery, be sure that
the included AC adapter is properly attached to the converter/battery pack and
connected to an outlet delivering proper voltage.
·
The blue LED
on the battery is not on.
Check to see if
the power switch is in the on position. If it is not, then turn the battery on.
If the battery is in the on position and the blue LED is still not lit, then
your battery probably needs to be recharged. Plug the AC adapter into the wall
and into the battery to charge your ezVision battery.
·
Is the A/V or iPod cable connected properly?
Recheck the connection of the appropriate A/V cable.
For iPods... The white end of the cable must be plugged into the iPod and the
black end into the ezVision battery.
·
Is iPod set to Video Mode?
In order to use
the ezVision Video iWear with an iPod, you must go to the Videos menu on the iPod
then go to Video Settings and change TV Out to "ON". See connecting to your iPod
section for more details.
Back to top
·
Has the protective film been removed from both screens?
The ezVision is
shipped with small protective film covers over the two screens. These must be
removed before viewing any content. Please refer to the illustration in this
manual to be sure you are aware of the location of and procedure for removing
the protective film.
·
Is the
external device (program material) connected?
Double check if
the device you are using is properly connected to the ezVision. Photos and
descriptions of proper set-ups are available in this manual.
·
Do the screens need to be cleaned?
After time, some
residue may build up on the ezVision's screens. Cleaning them with a clean, soft
cloth is recommended. Clots and cleaners manufactured for use on eyeglasses are
a good choice for use with your ezVision. Treat the screens as you would a pair
of eyeglass lenses, exercising care not to scratch the screens. Abrasive
cleaners could permanently damage your ezVision.
Back to top
·
Is the volume turned up?
Slowly turn up the volume control on the battery pack/converter. Be careful,
prolonged exposure to loud sounds may permanently damage your hearing.
·
Is the sound output of your player muted?
Some devices, including iPods, portable DVD players and even some home DVD
player models have their own volume control and muting functions. Be sure that
the connected device is not muted and the volume is not set at zero.
Back to top
Baru BR-3000:
·
Do not supply to the device. Please use the power adapter to supply power.
Back to top
·
The device
was in standby status. Please press POWER button to wake up it. Make sure that
you select proper input source for TV, and connect the device with TV correctly.
Back to top
·
Mute
function is on. Please press MUTE button to turn off.
·
If the audio is
output to a amplifier, make sure you turn on the power of amplifier.
Back to top
·
Point the
remote to the device, and use the remote within 5 meters from the device.
·
Maybe you need
replace the battery.
Back to top
·
Make sure you
install the HDD properly
·
Make sure there
are only primary partitions in HDD; Extend and logic partitions may not be
recognized
Back to top
·
Make sure
partitions of HDD is FAT format (not NTFS). The file which the device doesn' t
support won't how on TV.
Back to top
·
There are too
many photos or music in the HDD partition. It will take a long time to start
music-slide-show
Back to top
·
Use the power
adapter in instead of the bus-power. Use double USB plugs to get bus-power can
solve your problem in case the capacity of HDD is below 40G
·
Make sure you
install USB drive in the OS when you use WIN98
Back to top
·
Make sure you
didn' t press COPY key in the course of coping. COPY key is used to start coping
and, to break coping too.
·
The USB slave
device does not compliant with our products, the file system in the USE slave
device must be FAT
Back to top
·
The connection
of AV wire is not correct. Reconnect the AV wire
·
The TV which
use for preview the video doesn't choose the correct channel. Change to the
correct channel
·
The equipment
which sends out the video signal is work deviant. Check the situation of the
equipment
·
Sudden
interrupt during the record. That is a bad file. This is not a fault
·
There is some
bad track. Use the software to repair the bad track
·
That is not
support the file, if it can't be displayed on PC. Update the software or change
to another one
Back to top
·
The power of
the DVR connects weak or be cut off suddenly. Check the power is fastness
·
Hard disk is
full. Clear up the hard disk
·
Maybe you need
defrag your HDD
·
Don't put
corrupted file in the HDD. Correct file can' t be played normally after a
corrupted file is played
Back to top |
